This content requires the base game Train Simulator 2019 on Steam in order to play.

## About This Content
The BORAIL wagons were an interesting group that found themselves built in the
revenue series of wagons although they would find themselves often used as
special wagons and for the Civil Engineer. The primary use for the wagons was
the transportation of lengths of new rail from the rolling mills to either
track prefabrication plants or to docks for export. Given that the standard
length of rail was 60ft the BORAIL wagons measured 62ft over headstocks and
were fitted with bolsters to support the load.

There were two variations of BORAIL constructed with different types of
traffic in mind. By far the largest group were those 135 built to dia. 1/483
with 5 bolsters for the carrying of finished rail for fabrication or export. A
further 30 wagons were constructed using the same under-frame but without the
bolsters. These wagons were designed for carrying pre-stressed concrete beams
and had flush sockets on the deck to locate stanchions as required.

Although designed with two specific traffic uses in mind photographs show that
they were looked on as ‘handy’ for a number of other uses including carrying
vehicles. Naturally they were pressed into service to carry items longer than
other bolster wagons could handle without the need for runner wagons. However,
they also seem to have found a lot of use in carrying exceptional loads either
as spacers or for carrying the load itself. In some pictures the bolster
fitted wagons can be seen with their bolsters removed to carry alternative
loads including deck sections for the Humber Bridge.

The 1970’s and 1980’s saw a large program to convert existing wagons to the
air braking system as British Rail attempted to modernise and increase the
speed and profitability of it’s freight services. The vast majority of the
BORAILS (150 out of 165 constructed) passed through the BR works in Shildon
for air brake conversion that was to radically change the appearance of the
wagons.

The bogies were replaced with 1.8m wheelbase Y25C bogies fitted with hand
brake wheels. Alongside this the body was totally rebuilt with new 8-inch high
sides with six (later 8) pockets for ratchet tensioners to allow the use of
nylon straps for securing loads, a new deck was fitted along with six new
bolsters. The mounts for the original securing rings were retained and used to
support the new body and the wagons were finished in Railfreight flame red and
grey livery.

However, the membership of the revenue fleet was to be short lived as in early
1983 the entire fleet was transferred to the Civil Engineers department where
they gained the TOPS code YLA and FISHKIND of ‘Mullet’, generally stencilled
on a central yellow panel along with a DC prefix to the number. Eventually the
wagons gained the engineers yellow and grey livery. Many of the wagons gained
additional ratchet tensioners both to increase those originally fitted with 6
tensioners per side to 8 or in some quite random locations possibly related to
a specific load at some point.

In about 1985 around 10 wagons were converted by the Southern Region for the
carrying of track panels by removing the bolsters and fitting heavy
longitudinal timbers to raise the load above the deck rails. Initially the
wagons gained the TOPS codes of YMA but retained their fishkind of Mullet.
However, (possibly due to confusion) they gradually started gaining the
fishkind of Parr. At this point the story becomes a little uncertain as these
initial conversions then appear carrying concrete sleepers complete with the
TOPS code of YQA but still retaining their original bodywork often with an
additional tensioner at the mid-point if this had not been fitted at the point
of the earlier conversion to air brakes.

At around the same a time a larger number of YLA Mullets were converted
specifically for carrying concrete sleepers. These also lost their bolsters in
favour of the longitudinal timbers but topped off with thinner timber strips.
At the same time the bodywork was modified to include a step at the outer ends
on both sides. Other conversions involved the fitting of more tensioners to
number 13 per side along with the steps at the end to a slightly different
style.

Ultimately there were some 69 conversions for sleeper carrying and they all
ended up carrying the TOPS code of YQA and fishkind of Parr. This pack
attempts to give the general feel of the confused history of these wagons and
makes a distinction in the naming that YMA Mullets are track panel carriers
and YQA Parrs are sleepers carriers. However, there is a bit of randomisation
once the wagons are in the simulator to reflect the confused coding and naming
of the earlier conversions.

The YQA Parr Wagon Pack for Train Simulator features
* YQA Parr sleeper carrier and YMA Mullet track panel carrier models in Engineers ‘Dutch’ livery
* Clean and Weathered textures
* Empty and Loaded versions with suitable physics
* Animated hand brake wheels
* Randomised body style for the YMA
* Intelligent tail lamps

The pack includes a user manual with further details about the rolling stock
and the customising of some of the features when using the wagons in
scenarios.

TS Marketplace: YQA Parr Wagon Pack